|
What this covers
|
On a tunnel project budget, consumables are small line items. The machine, the lining and the shafts take most of the money. Grout, grease and brushes barely register.
On site, the picture is reversed. When a drive stalls, leaks or settles, the cause is often a consumable that was chosen out of habit. If you design, specify or build tunnels, it is worth knowing where these materials sit in the decision chain and what to ask for each one.
What Counts as a Tunnel Consumable
Tunnel consumables are the materials used up as the machine advances, as opposed to the machine itself or the permanent lining. The main ones are:
|
Consumable |
Where it works |
What it does |
|
Annular grout or lubricant |
Between the pipe or shield and the ground |
Lubricates, supports the overcut and controls water |
|
Tail seal grease |
In the chambers between tail seal brush rows |
Fills gaps and carries pressure at the tail of the shield |
|
Tail seal brushes |
At the back of the shield |
Keep contact with the lining and hold the grease in place |
|
Main-bearing sealant |
Around the main bearing of the cutterhead |
Fills gaps formed as the cutterhead turns and keeps soil and water out |
|
Soil conditioning and ground improvement products |
At the face and in the excavated soil |
Change how the soil flows and behaves during excavation |
Each one affects a different risk. Together they cover friction, settlement, water ingress and machine protection.
Who Chooses Them
On most projects, the chain runs like this. The owner sets the goal. An engineering firm designs the tunnel. A design consultant writes the material specification. The contractor buys and installs.
That chain matters because influence and risk sit at different points. The consultant has the most influence before construction, when the spec is written. The contractor carries the problem when something goes wrong on site. If the spec says little about consumables, the contractor chooses by habit, and the consultant has nothing to point to when performance falls short.
Why Habit Is a Risk
Habit is not always wrong. A material that worked on the last ten drives may work on the eleventh. Contractors build habits for good reasons: a known material is easier to mix, pump and troubleshoot, and crews know how it behaves. That experience is valuable and worth keeping.
The risk comes when the ground changes. A lubricant that worked in clay may lose its film in water-bearing sand. A grease that held at shallow depth may struggle at higher pressure. A brush that coped with a straight drive may wear quickly on tight curves. The material did not change. The job did.
A short spec section for each consumable, tied to the geotechnical report, makes sure someone checks the match before the drive starts.
Matching Consumables to the Ground
The geotechnical report already contains most of what you need to choose consumables. The trick is to read it with each material in mind.
|
Ground condition |
Annular grout priority |
Tail seal priority |
|
Fine, low-permeability soil |
Lubrication over the drive length |
Standard filling, watch consumption |
|
Permeable, water-bearing sand or silt |
Retention under water pressure |
Wash-out resistance and full chambers |
|
Artesian aquifer at launch |
Sealing at the portal and entrance ring |
Pressure capacity from the first rings |
|
Deep alignment |
Pressure capacity in the annulus |
Depth rating and the conditions it depends on |
|
Tight curves |
Filling the larger gap on the outside |
Brush elasticity and grease malleability |
|
Under sensitive assets |
Annular support for settlement control |
Avoiding stoppages that invite leaks |
A table like this in the design report gives the consultant a direct line from ground to material. It also makes a substitution request easier to judge, because the question becomes simple: does the proposed material meet the priority for this stretch of ground?
The same table helps the contractor plan stock. Stretches that need a premium grease or a modified grout can be scheduled for delivery ahead of time, rather than discovered when the machine is already in them.
Annular Grout and Lubricant
For pipe jacking and TBM drives, the annular material has three jobs: lubrication, support of the annular gap, and water control. In permeable, water-bearing ground, the hard part is keeping the material in place.
Ask for evidence that it holds under water pressure, such as a sustained constant pressure test, and for a field record in comparable ground. Ask how it is mixed and pumped, and how long it takes to make and ship.
Field records with measured results are especially valuable here. One example is the Ligang water intake pipe jacking case: a 3,214.96 m single drive in DN 2600 steel pipe under the Yangtze River, where jacking force fell from 8,000 kN at a 300% injection rate with traditional bentonite to 6,778 kN at 150% after the lubricant was changed at section 77, about 15% lower. On the left line no intermediate jacking station was used, and on the right line one was used once, after a long stoppage.
Tail Seal Grease and Brushes
The tail seal is a system: brushes hold their shape and contact, grease fills the gaps and carries the pressure. A depth or pressure rating usually depends on the grease filling rate, the spacing between brush rows and the grease used.
Ask for the grease test results that matter: density, consistency, pumpability, malleability, adhesion, vertical wash-out and water sealing ability. Ask for the brush properties: compressive strength, wear resistance, toughness and elasticity, and corrosion resistance. Ask which grease the brush rating was based on, and confirm the lead time, since grease can take months to reach a jobsite.
Main-Bearing Sealant
The main bearing is one of the most expensive parts of a TBM to repair. Its sealant has to fill the gaps formed as the cutterhead rotates and keep soil and water out while the machine is excavating.
Tests for main-bearing sealant cover density, consistency, pumpability, adhesion, water resistance and water pressure sealing, and a dynamic leakage test gives a more realistic picture of performance in operation. Ask for those results in the submittal.
Support Matters as Much as Product
Consumables behave differently once they meet real ground. The first weeks of a drive are when parameters are set, and good settings at the start often become the reference for the rest of the job. The correct use of products and good parameter adjustment in the initial stage of a tunnel project often set the technical reference for the later excavation, which leads to more consistent and safer construction. Getting those first settings right is cheaper than correcting them later, once the machine is deep into the drive and every change has to be made under pressure.
That makes on-site support a real part of the purchase. Useful support includes:
- On-site debugging and guidance at startup, while parameters are being set.
- Laboratory analysis of samples from site when something looks wrong.
- Help choosing a ground improvement method for different soil layers.
- Training for crews on mixing, pumping and filling.
- A clear contact for questions during the drive.
A supplier with its own laboratory and field staff can usually provide all of these. One example is Balsam Laboratory, which states more than 25 years in the tunnel boring industry and materials used on more than 500 km of tunnels, and which offers tunneling materials and technical support from annular grout and tail seal grease to laboratory analysis, ground improvement advice and crew training.
Writing Consumables Into the Spec
You do not need a long document. A short section for each consumable, with the same structure, is enough.
- State the performance required.
- List the evidence required: test results, field records, safety data sheet.
- State the practical limits: pumping plant, latest delivery date.
- Require records on site: what was used, where, and what the machine did.
- Require supplier support at startup.
That structure works for grout, grease, brushes and sealant alike, and it keeps the comparison between suppliers fair.
It also keeps the spec short enough that people actually read it. A consumables section that runs to a page or two is far more likely to be followed on site than one buried in a long appendix. Keep the wording plain and testable, and put the ground table where the site team will see it.
Records That Pay off Later
Consumable records are easy to keep and easy to ignore. They are also the best source of real numbers for the next project.
Record grout volumes and jacking force per pipe or per ring. Record grease consumption per ring, with the ground type. Note stoppages and curves. At the end of the drive, write down what each consumable did in each ground type. That short summary turns the next bid from a guess into a plan.
The Short Version
Tunnel consumables are small on the budget and large on site. Annular grout, tail seal grease, brushes and main-bearing sealant each control a different risk.
Write a short section for each into the spec, tied to the ground. Ask for test results, field records and practical supply details, include on-site support in the purchase, and keep records that make the next project easier to plan.

